← Back   Our Equipment » Boom Pumps » 39m Putzmeister Concrete Boom Pump

39m Putzmeister Concrete Boom Pump

Putzmeister 39Z-Meter | 4 section Multi-Z | OSS outrigger system

Premier calls this one the jack of all trades, and the spec sheet backs it up. 38.3 metres up, 33.6 metres out, and a four section Multi-Z boom that opens in 9 metres. It handles general high-rise work from the ground, covers commercial slabs and residential foundations, and thanks to Putzmeister’s OSS outrigger system it sets up in a smaller footprint than a boom this size normally needs.

38.3 m vertical reach
Typically on site within 24 to 48 hours of booking
Or call 519-942-3410  |  Toll free 1-866-942-3410

Other sizes in the fleet

Some pumps in the fleet exist for one kind of job. This one exists for all of them. 38.3 metres vertical, 33.6 horizontal, 24 metres of reach below grade, on a four section Multi-Z boom that opens in 9 metres of headroom. That covers general high-rise pumping from ground level, commercial slabs, and ordinary residential foundations, which is why it is one of the busier trucks Premier runs.

Multi-Z is a Putzmeister design that folds the sections against each other more compactly than a standard Z, so the boom stows low and opens without the wide sweep a conventional four section needs. Paired with the OSS outrigger system, which narrows the outrigger footprint while still letting the boom use its full reach on the supported side, the result is a truck that takes up less of your site than its reach would suggest.

Output is 160 m³/hr rod side on the standard pump kit. Putzmeister also builds this boom with a heavyweight high pressure kit for long-distance work, which is worth mentioning if your pour involves a long line run rather than boom placement. Every booking includes an ACPA certified operator. Premier does not rent equipment without one.

Typical applications: general high-rise pumping from grade, commercial floor slabs and pads, residential foundations and ICF walls, deep excavations and sloped lots, light industrial work.

Figures below are taken from the Putzmeister 39Z-Meter manufacturer brochure, not from summary listings elsewhere on the site. Pump figures are for the 39Z.16H kit, the configuration Putzmeister lists as standard on this chassis.

📏 Reach and Boom

Vertical reach38.3 m (125’8″)
Horizontal reach33.6 m (110’3″)
Reach from front of truck30.7 m (100’9″)
Reach depth24.0 m (78’9″)
Unfolding height9.0 m (29’6″)
Boom sections4, Multi-Z fold

⚙️ Output and Pressure

Output, rod side160 m³/hr (210 yd³/hr)
Output, piston side108 m³/hr (141 yd³/hr)
Pressure, rod side85 bar (1,233 psi)
Pressure, piston side130 bar (1,885 psi)
Strokes per minute, rod side31
Stroke length2,100 mm (83″)

🔧 Pump and Hydraulics

Material cylinder230 mm (9″), hard chromed
Pipeline size125 mm (5″), metric ends
Hydraulic systemFree Flow, closed loop
Hydraulic pressure350 bar (5,075 psi)
Maximum aggregate63 mm (2.5″)
Water tank, pedestal700 L (185 gal)

🚛 Outriggers and Chassis

Outrigger spread, front6.0 m (19’8″)
Outrigger spread, rear8.1 m (24’7″)
Boom section lengths9.7 / 8.1 / 8.2 / 8.3 m
Rotation365 degrees
Overall length12.48 m (40’11”)
Total weight25,581 kg (56,395 lbs)

Putzmeister also offers this boom with the 39Z.13 HPD kit, rated 138 m³/hr rod side, which is the heavyweight option for high pressure and long distance pumping. The standard delivery line system is rated to a maximum line pressure of 85 bar (1,233 psi). Truck dimensions and weights are for the Mack MRU 613 the brochure specifies and vary with chassis and options. Need the full manufacturer document for a submittal package? Download the Putzmeister brochure PDF.

  • ACPA certified operator. Every Premier operator is trained and certified to American Concrete Pumping Association standards. The unit does not go out without one.
  • WSIB clearance certificate. Available on request for ICI and institutional prequalification packages.
  • Daily equipment inspection. Completed before the unit leaves the yard, documented, and available if your safety officer asks.
  • Lines, hoses and clamps for the configuration agreed at booking, including 2″, 3″, 4″ and 5″ line options.
  • Pre-pour site walkthrough on commercial and institutional jobs, so setup position, outrigger bearing and washout are settled before pour day rather than on it.
  • Backup equipment access. On large multi-day pours Premier can stage a second unit. Worth arranging at booking, not on the morning.
  • Unionized labour standards and OHSA compliance, as required on most commercial ICI sites.

Fuel, washout facilities and site access are the contractor’s responsibility unless agreed otherwise in writing at booking.

A mid-size boom with a smaller than usual footprint for its reach. These still need settling before the truck is dispatched.

  • Outrigger spread. 6.0 m across the front and 8.1 m at the rear, both hydraulically extended. The OSS system can reduce that footprint further where the site demands it, which is worth raising if the numbers look marginal rather than assuming the unit will not fit.
  • Ground bearing. 25,581 kg concentrated through four pads. Fresh backfill, buried services, basement slabs and septic beds all need review beforehand. Cribbing or pads may be required.
  • Overall length. 12.48 m of truck before outriggers. Check gate widths, turning circles and the access route.
  • Overhead clearance. The boom needs 9 m of unfolding height. On treed lots and older streets this is usually what decides the setup position. Premier will not set up under live lines.
  • Reach depth. 24 m below grade, so deep excavations are in range without extra line. The excavation needs to be shored with a clear path down for the boom.
  • Washout. A washout location must be nominated before the pour. Premier does not wash out to grade or to drains.
  • Rail corridors. Premier runs range limiting systems, so pours adjacent to rail are possible. Flag it at booking.

If overhead clearance is the constraint, the 38m 5-section opens in 7.4 m and the 32m ZZ in 5.65 m. Our guide to prepping a site for concrete pumping covers the rest.

Is the 39m Putzmeister the Right Pump for Your Pour?

Specify this unit when

  • General high-rise pumping from ground level, up to roughly twelve storeys before a placing boom becomes the better answer
  • Commercial slabs and pads where 33.6 metres of carry covers the pour from one setup
  • Residential foundations, ICF walls and footings on ordinary lots
  • Sites with a constrained footprint, where the OSS outrigger system reduces the ground the truck has to occupy
  • Deep excavations and sloped lots, with 24 metres of reach below grade

Use a different unit when

  • Genuinely tight urban access. Rear spread is 8.1 m and the boom needs 9 m to open. The 32m ZZ opens in 5.65 m and works in half the footprint
  • Pours needing the boom threaded through a gap. Four Multi-Z sections articulate less than five; look at the 38m 5-section
  • Carries beyond 33 metres or structures above twelve storeys. Step up to the 43m or 50m
  • Tower work above what a ground pump can service. That is a placing boom
  • Enclosed or indoor pours. Use the trailer and line pumps

How It Compares to the Units Either Side

UnitVerticalHorizontalBest for
38m 4-section Alliance37.1 m33.1 mStraightforward mid-size pours, fastest setup
39m Putzmeister Multi-Z (this unit)38.3 m33.6 mGeneral purpose, low-rise high-rise and commercial slabs
43m Alliance RZ42.5 m38.5 mLarge slabs, roof pads and deeper wall pours

The 38m and 39m units sit within about a metre of each other. Which one goes out usually comes down to what is available on your pour date and how much articulation the site needs, so it is worth asking rather than specifying by number.

Where the 39m Earns Its Place

The 39m does not have one specialty, which is precisely the argument for it. It is tall enough for general high-rise work from the ground, long enough for a commercial slab, and small enough that nobody blinks when it turns up on a residential foundation. On a mixed week it can do all three without anyone having to think about which truck is free.

Putzmeister’s OSS outrigger system is the part worth knowing about. It reduces the outrigger footprint while still using the boom’s full reach on the supported side, so the truck occupies less of the site than a conventional arrangement at this size would. For high-rise work, our guide to pump setup on high-rise projects covers where a ground level boom stops making sense and a placing boom takes over, and how to choose the right concrete pump is the general version of that decision.

Frequently Asked Questions, 39m Putzmeister

38.3 metres vertically from ground level at the truck, 33.6 metres horizontally, and 30.7 metres measured from the front of the truck. That covers roughly twelve storeys from a single ground level setup. The fleet listing rounds these figures; the ones here come from the Putzmeister brochure.

Outrigger spread is 6.0 m at the front and 8.1 m at the rear. The truck is 12.48 m long before outriggers and weighs 25,581 kg. The OSS outrigger system can reduce that footprint on constrained sites while still using the boom’s full reach on the supported side, so send the site plan rather than assuming it will not fit.

A Putzmeister fold pattern that stacks the four sections against each other more compactly than a conventional Z. The practical effect is a boom that stows low, opens in 9 metres of headroom and does not need a wide sweep to deploy. It gives up some articulation against a five section boom, so if the concrete has to be threaded around a structure the 38m 5-section is the better unit.

General high-rise, yes, up to roughly twelve storeys from ground level. Above that the arithmetic changes and a placing boom fed by a ground pump becomes the sensible arrangement rather than a taller truck. We will tell you which side of that line your project sits on before you book.

Yes. Every Premier unit goes out with an ACPA certified operator. Premier does not rent pumps as equipment only. The operator coordinates with your forming crew and handles setup, placement and washout.

160 m³/hr rod side and 108 m³/hr piston side on the standard .16H pump kit. Real world rate depends on the mix, the line configuration and how fast the ready-mix trucks cycle. Give us the volume and access and we will give you a figure to build the schedule on.

Popular Equipment

The units Ontario contractors book most often, alongside this one.

38m four section boom pump set up above a rock cut, placing a rural house foundation from formed footings below

38m Boom Pumps

Four and five section 38 metre units, effectively the same reach with different setup characteristics.

43m 5-section boom concrete pump

43m Alliance RZ

Four more metres up and five more out, for large slabs and deeper wall pours.

Placing boom and large boom truck pouring large slab Premier Concrete Pumping in Ontario

Placing Booms

The usual partner once a tower climbs past what a ground level pump can service. 36m and 38m units.

Check Availability for the 39m

Tell us the pour date, the volume, the storey count and where the truck can stand. We will confirm whether the 39m fits or point you at the unit that does. No obligation.

Need help selecting the right boom pump for your project?