← Back   Our Equipment » Boom Pumps » 50m Alliance Concrete Boom Pump

50m Alliance Concrete Boom Pump

Alliance JXLRZ 50-5.16 | 5 section RZ roll and fold | X-style outriggers

The first unit in the fleet that is genuinely a commercial pump. 49.3 metres up and 44.4 metres out on a five section RZ boom, which covers a mid-rise structure or a large commercial slab without repositioning. What makes it more flexible than its size suggests is the X-style outrigger arrangement, which can be set in more configurations than a fixed spread and gives the operator options on a constrained site.

49.3 m vertical reach
Typically on site within 24 to 48 hours of booking
Or call 519-942-3410  |  Toll free 1-866-942-3410

Other sizes in the fleet

Fifty metres is where a boom pump stops being a general purpose tool and starts being a commercial one. This unit reaches 49.3 metres vertically and 44.4 metres out, which covers a mid-rise structure or a large commercial floor from a single setup, and it does it with a five section RZ boom that opens in 10.8 metres of headroom.

The X-style outriggers are the detail worth knowing. On many pumps the outrigger spread is effectively fixed, so either the site takes it or it does not. X-style legs can be set in more than one configuration, which means on a constrained commercial site the operator has genuine options about where the truck stands and how the load is spread. That is why this unit ends up on sites that, on paper, look too tight for 37.5 tonnes of truck.

Output is 164 m³/hr rod side, the same pump kit as the 38m and 43m, so the difference you are paying for is reach and stability rather than volume. On continuous commercial pours the ready-mix schedule is almost always the constraint. Every booking includes an ACPA certified operator. Premier does not rent equipment without one.

Typical applications: mid-rise commercial and institutional structures, large floor slabs, parkade decks, bridge abutments and retaining walls, water treatment structures, industrial pads with long carries.

Figures below are taken from the Alliance JXLRZ 50-5.16 manufacturer specification sheet, not from summary listings elsewhere on the site. Model designation JXLRZ 50-5.16.

📏 Reach and Boom

Vertical reach49.3 m (161’9″)
Horizontal reach44.4 m (145’8″)
Unfolding height10.8 m (35’5″)
Boom sections5
Fold typeRZ roll and fold
Pipe diameter125 mm (5″)

⚙️ Output and Pressure

Output, rod side164 m³/hr (215 yd³/hr)
Output, piston side102 m³/hr (133 yd³/hr)
Pressure, rod side72 bar (1,044 psi)
Pressure, piston side115 bar (1,668 psi)
Strokes per minute31
Stroke length2,100 mm (83″)

🔧 Pump and Hydraulics

Concrete cylinder230 mm (9″), hard chromed
S-tube size9″ x 7″
Hopper capacity600 L, easy clean
Hydraulic pressure350 bar (5,076 psi)
Water tank800 L (211 gal)
Main oil pumpRexroth Hydromatic A11VLO260

🚛 Outriggers and Chassis

Outrigger styleX-style
Front spread8.7 m (28’7″)
Rear spread9.63 m (31’7″)
Boom section lengths9.63 / 7.41 / 7.8 / 9.98 / 10.5 m
Overall length12.8 m (42’8″), cab over
Total weight37,535 kg (82,750 lbs)

Piston side pressure of 115 bar is a system rating and is not to be used through boom pipe. Chassis figures are for the cab over configuration Alliance lists for this model. Need the full manufacturer document for a submittal package? Download the Alliance spec sheet PDF.

  • ACPA certified operator. Every Premier operator is trained and certified to American Concrete Pumping Association standards. The unit does not go out without one.
  • WSIB clearance certificate. Available on request for ICI and institutional prequalification packages.
  • Daily equipment inspection. Completed before the unit leaves the yard, documented, and available if your safety officer asks.
  • Lines, hoses and clamps for the configuration agreed at booking, including 2″, 3″, 4″ and 5″ line options.
  • Pre-pour site walkthrough on commercial and institutional jobs, so setup position, outrigger bearing and washout are settled before pour day rather than on it. On a unit this size that walkthrough is worth taking up every time.
  • Backup equipment access. On large multi-day pours Premier can stage a second unit. Worth arranging at booking, not on the morning.
  • Unionized labour standards and OHSA compliance, as required on most commercial ICI sites.

Fuel, washout facilities and site access are the contractor’s responsibility unless agreed otherwise in writing at booking.

At 37.5 tonnes this is a serious piece of equipment and the site has to be assessed properly. None of this is unusual on a commercial job, but all of it needs settling before the truck is dispatched.

  • Outrigger spread. 8.7 m across the front and 9.63 m at the rear. Allow a clear area of roughly 10 m each way. The X-style legs give more than one setup configuration, so if the footprint is marginal, send the site plan rather than assuming it will not fit.
  • Ground bearing. 37,535 kg concentrated through four outrigger pads. This is the single most important item on the list. Basement slabs, fresh backfill, buried services, vaults and septic beds all need engineering review, and cribbing or spreader pads are commonly required.
  • Overall length. 12.8 m of truck before outriggers. Check gate widths, turning circles and any switchback on the site access road.
  • Overhead clearance. The boom needs 10.8 m of unfolding height. Power lines, adjacent structures and crane paths inside the working radius all need identifying in advance. Premier will not set up under live lines.
  • Washout. A washout location must be nominated before the pour. Premier does not wash out to grade or to drains.
  • Rail corridors. Premier runs range limiting systems, so pours adjacent to rail are possible. Flag it at booking, it changes the setup.

If the ground will not take it, the 43m is about 6 tonnes lighter. Our guide to pump setup on complex sites covers ground bearing and confined setups in more detail.

Is the 50m Alliance the Right Pump for Your Pour?

Specify this unit when

  • Mid-rise commercial and institutional structures, roughly fifteen storeys from a single ground level setup
  • Large commercial slabs and parkade decks where 44 metres of carry means one setup instead of two
  • Sites where the ready-mix truck has to stay on the road while the concrete goes well inside the footprint
  • Bridge, abutment and water treatment structures needing long horizontal reach at moderate height
  • Confined commercial sites, where the X-style outriggers give the operator more setup options than a fixed spread would

Use a different unit when

  • Residential foundations and standard slabs. A 38m or 43m does that work for considerably less money
  • Tight urban infill. At 37.5 tonnes and nearly 10 m of rear spread, this is a lot of truck. The 32m ZZ is the tight access unit
  • Ground that has not been assessed. Soft fill and fresh backfill are a real constraint at this weight
  • High-rise cores above roughly fifteen storeys. That is a 65m or a placing boom
  • Basement, indoor or low-clearance pours. Use the trailer and line pumps

How It Compares to the Units Either Side

UnitVerticalHorizontalBest for
43m Alliance RZ42.5 m38.5 mLarge slabs and wall pours, about 6 tonnes lighter
50m Alliance RZ (this unit)49.3 m44.4 mMid-rise and large commercial, X-style setup options
52m Putzmeister Multi-Z52 m48 mUrban mid-rise on tight sites
65m Alliance RZ64.5 m59.6 mHigh-rise cores and the longest carries

Figures for the 52m come from Premier’s fleet listing rather than a manufacturer sheet, so treat them as approximate. The 43m and 65m figures are from their spec sheets.

Where the 50m Earns Its Place

This is the unit for commercial work that has not yet become high-rise work. Mid-rise residential and institutional structures, large commercial floor slabs, parkade decks, water treatment and infrastructure pours where the placement point is a long way in from wherever the ready-mix can park. On the bigger jobs it often works alongside another pump rather than alone, which is how the large slab in the gallery above was run.

The X-style outriggers are worth understanding if your sites are awkward. Rather than one fixed spread, they can be positioned in several configurations, so on a constrained commercial site the operator has real options about where the truck sits. That flexibility is the reason this unit gets onto sites its weight class would normally rule out. If you are running a job that may need more than one pump, when you need multiple concrete pumps covers how that gets scheduled, and choosing a pump size for a commercial project works the sizing from the estimator’s side.

Frequently Asked Questions, 50m Alliance

49.3 metres vertically from ground level at the truck, and 44.4 metres horizontally from the boom pedestal. That covers roughly fifteen storeys from a single ground level setup, or a large commercial floor slab without moving the truck.

Allow a clear area of about 10 metres each way. Outrigger spread is 8.7 m at the front and 9.63 m at the rear, and the truck is 12.8 m long before outriggers. Because the outriggers are X-style there is usually more than one workable configuration, so send us the site plan before ruling it out.

Total weight is 37,535 kg and it concentrates through four outrigger pads, so this is the question that matters most on this unit. Basement slabs, fresh backfill, buried services and vaults all need review, and cribbing or spreader pads are common. Premier will walk the site with you before pour day on commercial and institutional jobs.

Instead of a single fixed spread, X-style legs extend on a diagonal and can be set in more than one configuration. On a confined commercial site that gives the operator real options about where the truck stands and how the load is distributed. It is the main reason a unit this heavy gets onto sites that look too tight for it on paper.

Yes. Every Premier unit goes out with an ACPA certified operator. Premier does not rent pumps as equipment only. The operator coordinates with your forming crew and handles setup, placement and washout.

If the placement point is within about 38 metres of where the truck can stand and the structure is under thirteen storeys, the 43m does the same job for less money and needs less ground. The 50m earns its place when the carry is genuinely longer, the structure is taller, or the pour is large enough that a second setup would cost more than the bigger unit. Send us the numbers and we will tell you honestly.

Popular Equipment

The units Ontario contractors book most often, alongside this one.

43m 5-section boom concrete pump

43m Alliance RZ

Six metres less reach for roughly 6 tonnes less truck. The better call whenever it reaches.

65m concrete boom pump at Niagara Hospital

65m Alliance RZ

The longest reach in the fleet, for high-rise cores and the longest carries.

Placing boom and large boom truck pouring large slab Premier Concrete Pumping in Ontario

Placing Booms

The usual partner once a structure climbs past what a ground level pump can service. 36m and 38m units.

Check Availability for the 50m

Send the pour date, the volume, the storey count and where the ready-mix can stand. We will confirm whether the 50m is the right unit or point you at a better fit. No obligation.

Need help selecting the right boom pump for your project?